INFINITY 710 ECU
Hinta 3 470,60 € (ALV. 24%)
Kysy meiltä lisää tästä tuotteesta

30-7100
Infinity 708 sisältää 8 sytytyslähtöä sekä 8 suutinlähtöä. Prosessoriteholtaan tehokkain suorituskyky markkinoilla!
Liitännöiltään monipuolisempi kuin 5 -sarja, esim 4*VVT/VANOS, 2* DBW -sähkökaasu, enemmän sisään/ulostuloja yms.
Tarkemmat tiedot löydät englanninkielellä alempaa virheiden välttämiseksi.
TOIMITUSTUOTE. TOIMITUSAIKA PÄÄSÄÄNTÖISESTI N. 1 VIIKKO, JOKA VARMISTETAAN TILAUKSEN JÄLKEEN.
Asennusmanuaali:
Toimituskulut
- Nouto lähimmästä postista
- 0,00 €
- Nouda tilauksesi valitsemastasi postista. Perillä LÄHETYKSESTÄ seuraavana päivänä pääsääntöisesti koko maassa. LOPPUSUMMALTAAN YLI 200€ TILAUKSET ILMAN TOIMITUSKULUJA TÄLLÄ TOIMITUSTAVALLA
- Posti Express-paketti
- 0,00 €
- Nopein toimitustapa koko Suomeen. Posti Express tuodaan LÄHETYSpäivää seuraavaksi päiväksi klo 14-16 mennessä suoraan asiakkaalle tai lähimpään toimipisteeseen, ellei asiakasta tavoiteta. Tilattava klo 12 mennessä saman päivän lähetykseen.
- Postin Kotipaketti
- 0,00 €
- Posti tuo tilauksesi haluamaasi osoitteeseen ilmastoystävällisenä Posti Green-lähetyksenä, ja soittaa ja sopii kanssasi sopivimman toimitusajankohdan.
- Nouto etukäteen sovittuna
- 0,00 €
- Käytä vain mikäli olet sopinut ETUKÄTEEN tuotteen noutamisesta sovittuna ajankohtana sovitusta paikasta. VELOITAMME RAHDIN CHECKOUT -MAKSUNA ETUKÄTEEN, MIKÄLI TUOTE PITÄÄKIN LÄHETTÄÄ. (muutosmaksun pienlaskutuslisä 5€)
Tilauksesi tuotteet voidaan toimittaa seuraavilla toimitustavoilla.
Maksutapa



200MHz Prosessori joka pystyy 400MIPS (million of instructions per second) nopeuteen. Tietääksemme nopein jälkiasennusmoottorinohjaukseen tarkoitettu prosessori tällä hetkellä.
Kaikki Infinity moottorinohjaukset toimitetaan kaikki toiminnot aktivoituna, ei tarvetta ostaa lisätoimintoja erillistä maksua vastaan
Ilman virtauksen mallintamiseen perustuva polttoaineensyötön määrän laskenta. Vähentää korjauskarttojen tarvetta, helpottaen näin säätämistä huomattavasti. Syötät vain perusarvot (iskutilavuus, sylinterien määrä, sytytysjärjestelmän tyyppi ja sytytysjärjestys) sekä valitset yhden tavan mallintaan ilmanvirtauksen määrää ja sytytystä, voit aloittaa säätämään VE (volumetric efficiency) karttaa kohdalleen.
InfinityTuner USER INTERFACE SOFTWARE
InfinityTuner is optimized for speed and performance. The software has the power to control a multitude of features found in today’s modern racecars, and features an advanced tuning Wizard to reduce set up time. An ECU Setup Wizard takes complex calibration setup work and simplifies it through a smart interface that features tabs for quick set up of vital engine functions. Each tab includes a description of the function.
InfinityTuner software is highly flexible. It allows you to choose from multiple strategies for boost control, idle control, traction control, charge air temp blend, launch control and more.
All controls in the Infinity ECU are synched to logged data which allows users to edit calibration data during log playback to minimize tuning time. AEMdata, AEM’s advanced data logging analysis software is also included for reviewing data logs.
ULTRA-HIGH RESOLUTION FUEL CONTROL The Infinity ECU calculates injector pulsewidth in units of 1/10th of a microsecond (0.0000001 second). Individual cylinder fuel trim is included and user adjustable.
ACCURATE IGNITION TIMING UNDER ANY CONDITION InfinityTuner software features a 3D ignition trim map (coolant and air temp based), and its back-end timing code is tested to 100,000 RPM. Individual cylinder ignition trim is included.
FLEX FUEL COMPENSATION Flex fuel compatibility is included, and the Infinity is able to make automatic adjustments for ethanol content in the fuel with the addition of an ethanol content sensor (sold separately).
MULTI-FUEL CAPABLE The Infinity has the ability to run two separate fuel types simultaneously through staged fuel injection
DRIVE BY WIRE CAPABILITY The Infinity Series 7 ECU can control two drive by wire throttle bodies and includes auto calibration for DBW sensors. It includes idle control, an optional drive by wire rev limiter (for use as a launch limiter, holding limiter or in conjunction with other rev limiters) and necessary failsafes based on redundant sensor inputs. Traction control via drive by wire will be added in the future at no additional cost for existing Infinity ECU owners.
IDLE CONTROL The Infinity ECU uses a coolant temp based idle control model. It includes an RPM vs. Engine Speed Rate idle decel feature that provides accurate control of the IAC and allows for adjustment of engine braking. The Infinity’s idle TPS offset provides smoother low idle operation when necessary, like driving in the pits or return lane following a pass.
MULTIPLE BOOST CONTROL STRATEGIES Choose from time, gear, vehicle speed, switch based or other boost control strategies. The Infinity’s boost control includes two 2D base duty tables and two 2D boost target tables. The second tables can be used as a trim, and users can choose from multiple strategies including IAT, MAP, Baro (kpa), throttle %, flex fuel content, boost target and more. Please visit our Forum for an in depth review of the Infinity’s boost control capabilities.
NITROUS CONTROL The Infinity’s software allows you to run a single-stage wet or dry nitrous set up (four-stage available soon). This feature includes nitrous timing delay to account for nitrous bleed out, and can be set up for water/methanol injection tuning. Four stage nitrous will be upgraded for free for existing Infinity users when it becomes available.
VARIABLE VALVE CAM CONTROL Set base duty, limit and VVC cam target for up to four cams through the InfinityTuner Wizard. Users are able to achieve a VVC cam target by setting Cam 1 base timing and base duty cycle % in a 2D table, and the software features a 1D base duty % table that controls the base duty cycle for the VVC output, which is tunable based on the VVC target.
MAP SWITCHING The Infinity includes up to four separate ignition maps, four separate Lambda maps and two separate VE maps with independent values. Using AEM’s 12 Position Trim Pot, this powerful feature delivers many valuable tuning options including:
- Multiple maps for multiple track conditions (practice map, rain map, qualifying map, FTW map)
- Change boost target
- Change Lambda target
- Change ignition target
- Tie boost, Lambda and ignition targets together and change them all
- Ideal for test mapping during tuning
- Change boost base duty
- Control PWM switches (like water/methanol injection)
- Choose between 2 VE tables for VVC or when restrictors are in place
- Blend between flex fuel ignition maps
- Blend by cam position and gear
ENGINE PROTECTION Multiple engine protection strategies are incorporated into the Infinity ECU. Available strategies include:
- MAP (create limp mode using Assumed Pressure Ratio table to compensate for pressure if sensor fails)
- Overboost (boost fuel cut until boost/throttle decreases)
- Fuel pressure (injector flow compensated for variations in pressure, sensor required)
- Oil pressure (trigger light or limit RPM if pressure drops below set value, sensor required)
- RPM (rev limiter)
- Coolant temperature, Temp vs. RPM (fuel and ignition cut, sensor required)
- Knock control with feedback
- Lean protection (fuel and ignition cut)
REAL-TIME ADVANCED DIAGNOSTICS The Infinity’s diagnostics software can be configured to constantly monitor signal and current quality to alert the user of a potential issue before it creates the potential for engine damage.
INTERNAL WIDEBAND CONTROLLER Dual Bosch wideband controllers are built into Infinity Series 7 ECUs. This provides highly accurate closed-loop AFR targeting and enables the sensor diagnostics in the ECU to determine the operational condition of the sensor.
LIGHTNING-FAST DATA LOGGING Infinity’s logging feature supports 2 different file systems. A custom file system option will support 100 channels at up to 1 KHz using a high performance USB flash drive (sold separately). A standard FAT file system will support 10 channels at up to 1KHz, 20 channels at up to 500Hz or 100 channels at up to 200Hz. The Infinity includes a 4GB USB memory stick and the user can replace this with up to 64GB. Additionally, the user can also log direct to the PC at up to 500Hz when connected.
AEMdata DATA ANALYSIS SOFTWARE AEMdataprovides an advanced interface for viewing the log files generated by the Infinity ECU.
DUAL KNOCK SENSING Dual knock signal conditioning circuits allow for precise measurements of knock levels. The Infinity can utilize both Piezoelectric and Flat Response type knock sensors.
RELIABILITY The Infinity ECU is constructed using automotive-rated components designed to withstand the harshest racing environments. Its enclosure and connectors are sealed to make it suitable for engine bay mounting. An advanced wear-leveling strategy for flash memory ensures a lifetime of reliable performance.
COMMUNICATIONS The Infinity ECU is able to transfer data via USB at up to 480 Mb/second. It features a fully-sealed IP67 communications connection system.
NETWORK INTERFACES Infinity is AEMnet enabled and will communicate with another AEMnet-equipped device. It is able to output to 3rd party dash/logger devices (not all 3rd party dash/logger devices may be supported). Call AEM technical support at (310) 484-2322 for more information.
INFINITY ECU ADVANCED TUNING PACKAGE Certain Advanced Tuning functions, hardware outputs and sensor inputs are available for the Infinity Programmable ECU. The Infinity ECU's Advanced Tuning Package is available at no charge for a limited time. Please contact an Authorized AEM dealer or call AEM Performance Electronics at (310) 484-2322 for more info.
INFINITY SERIES 7 EMS CAPABILITIES:
- Airflow model based calculations
- VE-based engine startup
- Multi-fuel capable
- Flex fuel compensated – fuel, ignition and boost with blend
- Multiple boost control strategies (time, gear, vehicle speed, switch and more)
- Drive by wire (with Advanced Tuning Package)
- 2-step programmable launch control (3-step with Advanced Tuning Package)
- Programmable traction control, 2-wheel speed or engine acceleration (4-wheel speed with Advanced Tuning Package)
- No-lift shift (Requires Advanced Tuning Package)
- User configurable soft-cut rev limiters
- User configurable anti-lag
- Map switching (4 Separate ignition maps, 4 separate Lambda target maps, 2 separate VE tables)
- Single stage wet or dry nitrous control (4-stage with Advanced Tuning Package, coming soon)
- Integrated engine protection strategies
- Target Lambda table, 10x10
- Open-loop fuel pressure compensation
- O2 lean-out protection
- 2-channel adaptive knock control
- Configurable coil dwell (RPM, voltage and load based)
- Individual cylinder ignition trim (RPM based)
- Individual cylinder fuel trim (RPM based)
- 3D ignition trim maps (coolant and air temp)
- Real-time sensor diagnostics
- Ignition table, 20x20
- VE airflow table, map vs. engine speed, 20x20
- User adjustable charge temperature blend (CLT/AIT, engine speed dependent)
- Idle control (stepper and pulsewidth)
ADVANCED TUNING PACKAGE: Advanced Tuning Functions:
- No-lift shift
- 4-wheel speed traction control
- 3-step launch control
- Drive by wire
- 4-stage nitrous control (coming soon)
Advanced Tuning Hardware Outputs:
- 1 high side driver
- 2 H-bridge channels
Advanced Tuning Inputs:
- 2 analog voltage inputs
- 2 VR/Mag differential pair inputs
- 1 digital/frequency input
- 3 analog temp inputs
SPECIFICATIONS | PN: 30-7101 | INFINITY 710 PN: 30-7103 | INFINITY 712 PN: 30-7111 |
---|---|---|---|
2-Stroke Engines | Yes | Yes | Yes |
4-Stroke Engines | Yes | Yes | Yes |
Cylinders | Up to 8 | Up to 10 | Up to 8 |
High Impedence Injectors | Up to 8 | Up to 10 | Up to 12 |
High Impedence Injectors (Sequential) | Up to 8 | Up to 10 | Up to 8 |
Low Impedence Injectors | Up to 8 | Up to 10 | Up to 12 |
Low Impedence Injectors(Sequential) | Up to 8 | Up to 10 | Up to 8 |
Coils (0-5V Falling Edge) | Up to 8 | Up to 10 | Up to 8 |
Digital Inputs | Up to 8 | Up to 8 | Up to 8 |
VR/Mag Inputs | Up to 6 | Up to 6 | Up to 6 |
Analog Voltage Inputs | Up to 17 | Up to 17 | Up to 17 |
Analog Temp Inputs | Up to 6 | Up to 6 | Up to 6 |
Knock Control | 2-Channel | 2-Channel | 2-Channel |
On Board Wideband Air/Fuel Controllers | 2 | 2 | 2 |
Drive-By-Wire | Dual | Dual | Dual |
H-Bridge Channels | 2 | 2 | 2 |
High Side Outputs | Up to 2 | Up to 2 | Up to 2 |
Low Side Outputs | 10 | 10 | 10 |
Low Side Outputs that can be PWM | 10 | 10 | 10 |
4-Wire Stepper Motor Control | Yes | Yes | Yes |
CAN Channels | 2 | 2 | 2 |
Boost Control (RPM, Time, Gear, VSS, Switch Input, Flex Fuel Content) | Yes | Yes | Yes |
Variable Cam Control | Up to 4 | Up to 4 | Up to 4 |
Engine Protection* | Yes | Yes | Yes |
Launch Control | Yes | Yes | Yes |
Nitrous Control | Up to 4-Stage | Up to 4-Stage | Up to 4-Stage |
Traction Control | Up to 4-Wheel Speed | Up to 4-Wheel Speed | Up to 4-Wheel Speed |
Data Logging | Up to 64GB | Up to 64GB | Up to 64GB |
Weather Resistant Sealed Electronics | Yes | Yes | Yes |
Connector Pins | 129 | 129 | 129 |
Enclosure Dimensions | 6.75" x 6" x 1.8" | 6.75" x 6" x 1.8" | 6.75" x 6" x 1.8" |
Weight | 24oz / 680.4g | 24oz / 680.4g | 24oz / 680.4g |
* Engine protection is programmable and can be coolant temp-, oil temp-, oil pressure-, AFR vs MAP, intake air temp-, knock- or fuel pressure-based.